Home/Products/PAC 28% industrial
GB/T 22627-2022 · Al₂O₃ ≥ 28% · Industrial

Polyaluminium chloride 28%,
the coagulant that does the first half of the job.

[ Al2(OH)nCl6−n ]m  ·  Al₂O₃ ≥ 28%  ·  Basicity 40–90%

A pre-hydrolysed coagulant for industrial wastewater, municipal sewage, paper and dyeing effluent. It works across pH 5–9 without the alkalinity crash of alum, and it is the destabilising step that makes any polymer downstream actually perform.

28%Al₂O₃ MINIMUM
40–90%BASICITY
5–9pH WINDOW
24 moSHELF LIFE
Al
Al
Al
Al
Al
Al
Al
Al
O
O
O
O
Pre-hydrolysed species — [Al₁₃O₄(OH)₂₄(H₂O)₁₂]⁷⁺ · the Al₁₃ Keggin ion
01 — Forms we supply

One chemistry,
three ways to unload it.

The Al₂O₃ content is fixed at 28% for the industrial grade; what changes is the physical form and therefore the handling. Choose by how the plant can receive and dissolve the product, not by price per tonne alone — labour is usually the larger number.

PAC-28 SD
28%
Al₂O₃ (spray-dried)
Basicity70–85%
Insolubles≤ 0.6%
Dissolution20–30 min
Spray-dried powder. Fastest to dissolve, highest basicity, the default for wastewater and sewage plants.
PAC-28 GR
28%
Al₂O₃ (granular)
Basicity60–85%
Insolubles≤ 0.6%
DustLow
Granular form for bulk handling and manual dosing rooms — less dust, slightly slower to wet out.
PAC-28 L
10%
Al₂O₃ (liquid)
Basicity60–80%
Density1.19–1.22 kg/L
Dose factor× 3 solid
Liquid at 10% Al₂O₃ for plants with storage tanks and no make-down labour. Dosed straight from the IBC.

Basicity is the ratio of hydroxyl to aluminium, expressed as a percentage. Higher basicity means less acid to neutralise and less alkalinity consumed in the water, but a shorter shelf life once dissolved. Powder is quoted per tonne of product, liquid per tonne of Al₂O₃ content — compare on the Al₂O₃ basis, never on wet tonnes.

02 — Technical data

What the COA will say.

The table below is the GB/T 22627-2022 envelope for the industrial 28% grade. Every shipment carries a COA with the actual values, and heavy metals are tested per batch, not per year.

ParameterSpecificationTest method / note
AppearanceLight yellow to yellow powderVisual
Al₂O₃ content≥ 28.0%GB/T 22627-2022, EDTA titration
Basicity40–90%GB/T 22627-2022; grade-specific value on COA
pH of 1% solution3.5–5.0Glass electrode, 25 °C
Insoluble matter≤ 0.6%Gravimetric
Arsenic (As)≤ 0.0005%ICP-MS
Lead (Pb)≤ 0.002%ICP-MS
Cadmium (Cd)≤ 0.0005%ICP-MS
Mercury (Hg)≤ 0.00005%ICP-MS
Hexavalent chromium (Cr⁶⁺)≤ 0.0005%Spectrophotometric
Shelf life24 months powder / 12 months liquidDry, sealed, 5–35 °C; liquid above 5 °C to avoid crystallisation
Standard: GB/T 22627-2022 (water treatment chemicals — polyaluminium chloride). This is the industrial grade and is not intended for drinking water; for potable duty use PAC 29% to GB 15892. SGS or CCIC inspection can be arranged per shipment.
03 — Mechanism

Why pre-hydrolysed
beats alum on cost and pH.

PAC arrives partly neutralised. That single fact explains its lower alkalinity demand, its wider pH window and why it works at water temperatures where alum is sluggish.

STEP 01

Speciation in seconds

PAC dissolves into pre-formed polynuclear species — chiefly the Al₁₃ Keggin ion, carrying a 7+ charge. Alum has to build those species in the water, which takes time, alkalinity and the right pH.

STEP 02

Neutralise and adsorb

The highly charged Al₁₃ species adsorb on colloids and neutralise the negative surface charge. This is the step that makes turbidity and colour colloidally unstable — and the step most plants under-dose.

STEP 03

Sweep floc and settle

At higher doses the aluminium precipitates as a hydroxide floc that enmeshes particles and settles them. This is why PAC still works when charge neutralisation alone is not enough — and why overdosing leaves residual aluminium in the water.

04 — Applications and dose ranges

Where PAC 28% earns its cost.

Doses are product per cubic metre of water, expressed as 28% powder. For the 10% liquid form multiply by roughly three. These are field ranges, not design values — a jar test on your own water takes an afternoon.

Industrial wastewater

Mixed factory effluent, chemical and pharmaceutical wastewater, landfill leachate pretreatment. Works where pH swings between 5 and 9.

50–300 g/m³ · 28% powder

Municipal sewage

Primary and tertiary coagulation, phosphorus removal and sludge conditioning upstream of a belt press or centrifuge.

20–80 g/m³ · 28% powder

Paper & board

Furnish and white-water clarification, rosin and AKD sizing retention, de-inking effluent.

0.5–3 kg/t paper

Textile & dyeing

Decolourisation and COD reduction ahead of biological treatment, plus sludge conditioning. Often followed by anionic PAM.

80–400 g/m³

Steel & metal finishing

Pickling rinse water, phosphating and electroplating wastewater, oily effluent after emulsion breaking.

60–250 g/m³

Coal & mineral processing

Slurry water clarification and thickener feed conditioning, usually with an anionic PAM downstream.

30–150 g/t solids

Not on the list? PAC 28% is also used in food processing wash water, aquaculture, and as a retention aid in recycled fibre. Tell us the turbidity, colour, alkalinity and pH — alkalinity is the figure most buyers forget, and it decides whether PAC or alum is cheaper.

05 — Preparation and dosing

Dissolve it properly
and half the dose disappears.

PAC is forgiving compared with polymer, but undissolved solids are inert — they settle in the tank and show up as turbidity in the treated water. These five steps are the difference between a working plant and a dosing headache.

Make-down and dosing

01Dissolve to 5–10% w/w. 50–100 kg powder per m³ of water. Higher concentrations are stable but hard to meter accurately.
02Stir at 200–400 rpm for 20–30 min. PAC dissolves quickly; what takes time is letting the insolubles settle out.
03Let the tank settle, draw from the clear layer. Or filter the stock through a 60–80 mesh screen before the dosing pump.
04Dilute to 1–5% for dosing. Feeding 10% stock into a small pipe gives poor mixing and local overdosing.
05Rapid mix 30–60 s, then flocculate. 200–400 rpm at the injection point, then 20–60 rpm for 10–20 minutes in the flocculation basin.

Five things that quietly ruin performance

Dosing into still water. PAC needs immediate dispersion. Without rapid mix it hydrolyses in a pocket and the rest of the flow is untreated.

Ignoring alkalinity. Below about 40 mg/L as CaCO₃, PAC cannot form floc properly. Check alkalinity before blaming the chemical, and add lime if needed.

pH outside 5–9. Acid water wastes product; alkaline water above pH 9 redissolves the floc as aluminate and the turbidity comes back.

Mixing PAC and PAM in one tank. The cationic aluminium and the anionic polymer neutralise each other. Separate tanks, separate injection points, 30–90 s apart.

Carbon steel tanks and lines. PAC solution is corrosive at pH 3.5–5. Use FRP, PP, PVC or rubber-lined steel; a mild steel tank will fail within a season.

06 — Packaging and logistics

Powder, granule or liquid —
whatever your unloading allows.

25 kg / 50 kg woven bag

PE-lined PP woven bag, 40 bags per pallet or loose in bundles. The standard export packing for both grades.

20–25 t per 20' FCL

1,000 kg jumbo bag

Four-loop FIBC with discharge spout for plants that unload with a hoist and dose from a bulk hopper.

18–20 t per 20' FCL

IBC / drum for liquid

1,000 L IBC or 200 L drum for liquid PAC, with a food-grade liner on the drinking-water grade.

18–20 t per 20' FCL
07 — Compliance

What we hold, and
what we do not.

The single most important sentence on this page: 28% is the industrial grade. It is not a drinking-water product, and no document we issue will make it one.

✓

GB/T 22627-2022

Produced and tested to the Chinese national standard for industrial polyaluminium chloride.

✓

ISO 9001 / 14001

Quality and environmental management certified across the six production sites.

✓

SGS / CCIC

Third-party inspection available per shipment, at buyer's request and cost.

✕

Not a drinking-water grade

For potable water use PAC 29% under GB 15892, produced under a hygiene licence. This page is the industrial product.

On 30%. Buyers sometimes ask for “30% PAC”. In the current standards the drinking-water grade is Al₂O₃ ≥ 29% and the industrial grade is ≥ 28%; 30% is an old trade shorthand, not a grade we produce. If your process was designed on 30%, the dose converts as ×30 ÷ 29 — we will run the numbers with you rather than quote a product that does not exist.

08 — Questions buyers actually ask

Before you specify PAC.

Is 28% the same as the drinking-water grade?

No. 28% is the industrial grade under GB/T 22627-2022. Drinking water requires the 29% grade under GB 15892, with tighter heavy-metal and insolubles limits and production under a hygiene licence. Using the industrial grade for potable supply is not permitted, and we will not supply it for that purpose.

Why do people ask for 30%?

It is an old trade shorthand from earlier standards; the drinking-water grade is now specified as Al₂O₃ ≥ 29%. We produce 28% industrial and 29% drinking water, nothing in between. A plant that was designed on 30% should convert its dose as ×30 ÷ 29.

PAC or alum — which is cheaper?

Per tonne of product, alum is cheaper. Per cubic metre treated, PAC usually wins: lower dose, no alkalinity supplement, faster floc, and it works at low water temperature where alum is slow. Compare on total cost including lime and pH correction, not on the invoice.

What dose should I start with?

For municipal sewage, 20–80 g/m³ of 28% powder. For industrial effluent, 50–300 g/m³ depending on colour and COD. Run a six-point jar test from 10 to 200 mg/L — the optimum is usually sharper than people expect.

Can I get liquid instead of powder?

Yes — 10% Al₂O₃ liquid in 1,000 L IBC or 200 L drum, with roughly three times the dose of the powder per cubic metre. Liquid removes make-down labour but costs more per tonne of Al₂O₃ in freight. For flows above about 5,000 m³/d, liquid usually wins on total cost.

How is it packed and how much fits in a container?

25 kg or 50 kg PE-lined woven bags, or 1,000 kg jumbo bags. 20–25 t per 20' container in bags, 18–20 t in jumbos. Non-hazardous cargo; COA, SDS and packing list travel with the shipment.

Next step

Send the water analysis.
Get a dose and a cost per m³.

Turbidity, colour, COD, pH and alkalinity are the five numbers we need. Send them and you get a dose range, a jar-test protocol and a delivered cost per cubic metre — not a price list.

Reply within 12 working hours · data used for quotation only

Talk to us