Home/Applications/Textile
Dyeing · printing · finishing

Textile effluent: colour is
the expensive part.

Colour survives biological treatment. That is the whole problem: a plant can meet BOD and still fail on colour and COD because the dye molecule is designed to resist degradation. Coagulation is the only cheap way to take it out, and the chemistry has to match the dye class.

>90%COLOUR REMOVAL
55–75%COD REMOVAL
9–12TYPICAL pH
80–400g/m³ PAC
What goes into this water
PAC 28% industrialCoagulates the dye-colloid complex; the workhorse of decolourisation.80–400 g/m³
Cationic PAM C80High-charge grade for reactive and acid dye colour bodies.5–25 ppm
Anionic PAM A1210Settles the floc quickly in equalisation and batch tanks.2–10 ppm
Cationic PAM C50Dewaters the dye sludge on a filter press or centrifuge.4–8 kg/t DS
01 — Water profile

The dye class
decides the chemistry.

Reactive, acid, disperse, vat and sulfur dyes behave differently under coagulation. A program that works on one class fails on another — which is why “we tried PAC and it didn't work” usually means the dose or the class was wrong, not the product.

ParameterTypical rangeWhy it matters
pH9–12 (dyeing), 6–8 (mixed)Alkaline effluent needs pH adjustment before PAC or the dose doubles
Colour200–2,000 Pt-CoSets the coagulant dose almost linearly — colour is the design parameter
COD800–4,000 mg/LOnly 55–75% is removable by coagulation; the rest needs biology
Dye classReactive, acid, disperse, vat, sulfurReactive and acid dyes respond to cationic coagulants; disperse dyes need a different approach
Sulfide0–200 mg/L (sulfur dyes)Toxic to biomass and corrosive; oxidise before the biological stage
Salinity1,000–20,000 mg/LHigh salt from reactive dyeing reduces polymer efficiency and limits reuse
Give us the dye class and the colour figure and we can narrow the dose before the jar test. Give us only “textile wastewater” and the first test is a survey.
02 — Treatment train

The treatment train.

Equalise first, adjust pH second, coagulate third. Skipping the first two is how plants spend twice the chemical for half the result.

EQUALISATIONBalance tankDye batches arrive in slugs. 8–24 h retention is the difference between a stable dose and a daily crisis.—
pH ADJUSTNeutraliseBring 9–12 down to 6.5–8.0 before coagulation.acid + lime
COAGULATIONPAC 28%Rapid mix 60–120 s; dye colloids need more contact than turbidity does.80–400 g/m³
FLOCCULATIONCationic PAMSlow mix 10–15 min; colour body forms a visible floc.5–25 ppm
SETTLINGClarifier / DAFColour removed with the sludge; decanted water goes to biology.>90% colour
SLUDGEDewateringCationic PAM on the dye sludge; this sludge is bulky and hates being dried.4–8 kg/t DS

Sulfide-bearing effluent from sulfur dyeing must be oxidised before it reaches biomass or the polymer line — it consumes coagulant and it is toxic to the bugs.

03 — Recommended program

A program by dye class.

Reactive and acid dyes take the cationic route; disperse dyes often need more coagulant and less polymer.

On reuse. Decolourised effluent is often good enough for washing or cooling, but salinity and colour carry-over limit dyeing reuse. We will tell you where the limit is rather than sell a membrane you do not need yet.

04 — Dose reference

Dose by dye class.

Figures are for effluent at the stated colour load, after pH adjustment. Colour load, not flow, is the scaling parameter.

Dye classPAC 28%Cationic PAMExpected colour removal
Reactive dyes150–400 g/m³C80 10–25 ppm90–95%
Acid dyes100–300 g/m³C80 8–20 ppm90–96%
Disperse dyes200–400 g/m³C30 5–15 ppm85–92%
Vat dyes150–350 g/m³C80 10–20 ppm88–94%
Sulfur dyes (after oxidation)200–400 g/m³C50 8–20 ppm80–90%
Mixed printing wastewater250–400 g/m³C80 15–25 ppm85–92%
Colour removal above 90% is routine; COD removal is not. Coagulation takes out the dye and the colloidal COD, but dissolved organics — sizing agents, surfactants, urea — go to the biological stage. Design the two together.
05 — What goes wrong

Why decolourisation underperforms.

Four failures that account for most textile effluent problems we are asked to solve.

Coagulating at pH 10

Alkaline dyeing effluent consumes PAC neutralising alkalinity before it touches the dye. Adjust to 6.5–8.0 first; the same dose then does twice the work.

Judging by colour, not by floc

If the floc is small and slow, the polymer is wrong or underdosed even when colour looks acceptable. Watch the floc, not just the outflow.

Batch slugs into a continuous plant

Dye batches arrive in 20-minute slugs. Without equalisation the plant is either overdosed or underdosed most of the day, and averages hide it.

Treating dye sludge like biological sludge

Dye sludge is more compressible and more variable. It needs a higher charge density and a press, not a belt press set up for municipal cake.

The reuse question. Colour below 50 Pt-Co and COD below 200 mg/L is usually good enough for washing and cooling. Dyeing reuse needs salt control and a membrane step — coagulation alone will not get there, and pretending otherwise wastes a plant's capital budget.
>90%Colour removal
55–75%COD removal by coagulation
30–38%Cake from plate press
<50 Pt-CoReuse for washing
06 — Questions from plant engineers

Before you specify a decolourising program.

Why does PAC work better than alum on dye effluent?

PAC is pre-hydrolysed and carries highly charged Al₁₃ species, so it neutralises dye colloids with less alkalinity consumption and a wider pH window. On alkaline dyeing effluent that difference is large — often half the dose.

Cationic or anionic PAM for colour?

Cationic, at high charge density (C80), because the dye-colloid complex after PAC is still anionic. Anionic PAM is used downstream for settling speed, not for colour.

Can you handle sulfur dye effluent?

Yes, but the sulfide must be oxidised first — it is toxic to biomass and it consumes coagulant. After oxidation, PAC plus a C50 cationic grade works well; the colour removal ceiling is lower than for reactive dyes.

What dose should we budget for?

For reactive dye effluent at 500–1,000 Pt-Co, budget 150–400 g/m³ PAC and 10–25 ppm cationic PAM. Colour load drives it: if the plant dyes dark shades for a week, the dose goes up and there is no way around it.

Can the treated water be reused?

For washing and cooling, usually yes. For dyeing, salinity and residual colour limit reuse — that needs membrane treatment, and we will say so rather than let a plant buy chemical it cannot use.

Next step

Send the dye class and colour.
Get a dose, not a guess.

Dye class, colour (Pt-Co), COD, pH and daily volume. A 2-litre sample gets a jar test with colour and COD removal at four doses.

Reply within 12 working hours · data used for quotation only

Talk to us