Home/Applications/Pulp & paper
Retention · white water · deinking · sludge

Paper: retention economics,
measured in fibre and steam.

Every tonne of fibre that goes out with the white water is a tonne bought twice. The retention program decides how much of it stays in the sheet — and it is usually the cheapest upgrade available to a mill that has already optimised the machine.

85%+FIRST PASS RETENTION
<100 ppmWHITE WATER TSS
0.2–1.0kg/t CATIONIC
4.5–8pH RANGE
What goes into this water
PAC 28% industrialFixing agent — neutralises the anionic trash before the retention aid is added.2–8 kg/t paper
Cationic PAM C10 / C30Retention and drainage aid on the wet end.0.2–1.0 kg/t
Anionic PAM A1010Save-all and white-water clarification, and broke recovery.0.3–1.2 kg/t
Cationic PAM C50Sludge dewatering from the primary clarifier and DAF.3–6 kg/t DS
01 — Water profile

What the wet end
actually tells you.

Paper is the most instrumented customer group we sell to — there is data everywhere. These are the figures that decide whether a retention program will work or be fought by the chemistry of the furnish.

ParameterTypical rangeWhy it matters
Furnish pH4.5–8.0Acidic sizing runs need a different cationic demand and often a non-ionic grade
Conductivity500–5,000 µS/cmHigh closure raises anionic trash and consumes cationic polymer before it reaches the fibre
Filler content10–30%Filler has more surface area per gram than fibre, so it sets the polymer demand
Consistency at headbox0.5–1.2%Dose is per tonne of paper, but mixing quality depends on consistency
White water TSS200–2,000 ppmThe number that shows whether retention is actually working
Cationic demand50–600 µmol/LThe single best predictor of fixing-agent dose; measure it, do not guess
If a mill can tell us furnish pH, conductivity and cationic demand, we can usually name the program before the sample arrives. Without them, the first trial is really a measurement exercise.
02 — Treatment train

Where the chemicals go.

Retention chemistry is sequential: fix the trash, then bridge the fines. Reverse the order and both doses rise.

STOCK PREPThick stockRefining and blending. Cationic demand is highest here.—
FIXINGPAC 28%Into the thick stock or the machine chest, 60–120 s before the polymer.2–8 kg/t
RETENTIONCationic PAMAfter the fan pump, before the headbox. Shear here is high — expect some chain breakage.0.2–1.0 kg/t
WIREFormingFirst-pass retention measured here; target above 85%.—
SAVE-ALLWhite waterAnionic PAM clarifies the loop water and recovers fibre.0.3–1.2 kg/t
EFFLUENTClarifierCationic PAM on the primary sludge before the press.3–6 kg/t DS

On a closed mill the loop water carries the anionic trash back to the headbox, so the fixing-agent dose creeps up as closure increases. Budget for that when a mill moves to higher closure — it is not a polymer problem.

03 — Recommended program

Three products, one sequence.

Most mills need a fixing agent and one retention aid; the third product is for the save-all or the sludge line.

On the trial. A retention trial needs a machine trial, not a beaker: we ask for furnish, white water and the current chemical program, then supply samples with a dosing plan that the machine tender can actually follow on a shift.

04 — Dose reference

Dose reference.

Per tonne of paper unless stated. Retention doses are small and the make-down accuracy matters more than the grade choice at the margin.

DutyProductDoseTarget
Fixing agent (woodfree)PAC 28%2–5 kg/tCationic demand reduced to < 50 µmol/L
Fixing agent (high trash)PAC 28%5–8 kg/tStable first-pass retention
Retention aidCationic C10 / C300.2–0.6 kg/tFirst-pass retention > 85%
White water / save-allAnionic A10100.3–1.0 kg/tWhite water TSS < 100 ppm
Broke recoveryAnionic A10100.5–1.2 kg/tClear save-all filtrate
Primary sludge dewateringCationic C503–6 kg/t DSCake 25–32% DS
Retention aid overdose causes formation problems and sheet two-sidedness long before it shows up in the retention figure. Dose to the cationic demand and stop; more polymer is not more retention.
05 — What goes wrong

Why retention programs stall.

Four patterns we see repeatedly on machines that have already tried a retention aid and been disappointed.

Polymer consumed by trash

Without a fixing agent the cationic polymer is neutralised by dissolved anionic material before it reaches the fines. The mill concludes the polymer is weak; the real problem is sequencing.

Wrong shear point

Adding retention aid before the fan pump exposes it to the highest shear on the machine. Dose after the pump, before the headbox, and accept that some chain breakage is inevitable.

Under-hydrated solution

Retention doses are small, so a badly made-down solution is a large percentage error. Make down at 0.1–0.3% and check for gel particles weekly.

Ignoring closure effects

As the mill closes up, conductivity and anionic trash rise and the optimum dose moves. A program that worked at 60% closure may need a higher-charge grade at 90%.

The arithmetic. Improving first-pass retention from 78% to 86% keeps roughly 8% more fibre and filler in the sheet. On a 500 t/d machine that is 40 tonnes a day of raw material that no longer goes to the save-all, the clarifier and the landfill.
85%+First-pass retention
<100 ppmWhite water TSS
25–32%Sludge cake solids
2–8 kg/tFixing agent
06 — Questions from plant engineers

Before the machine trial.

Can you match the retention aid we already use?

Usually. Send the current TDS and a sample of furnish and white water; we run a focused trial on cationic demand, turbidity and drainage (SR or DFR) and compare against your existing product at equal cost per tonne.

Is a fixing agent always necessary?

No. Mills with low conductivity and clean furnish often run a retention aid alone. Above roughly 1,500 µS/cm or with high anionic trash, a PAC fixing step usually pays for itself in reduced polymer consumption.

What about neutral and acid sizing?

Acid systems at pH 4.5–5.5 often need a non-ionic PAM because the cationic demand profile is different and alum already provides the charge. We supply non-ionic grades for that case.

How is the product delivered to a paper mill?

25 kg bags on pallets, or 750 kg jumbos for bulk make-down. Most mills take a mixed container: PAC in 25 kg bags, PAM in 750 kg jumbos. Lead time from stock is 7–10 days.

Do you supply deinking mills?

Yes — PAC plus a cationic or anionic PAM depending on the ink system, and cationic PAM for the deinking sludge. Send the furnish mix and the clarifier load; deinking pulp has a higher anionic demand than virgin fibre.

Next step

Send the furnish and white water.
Get a retention plan.

Furnish mix, pH, conductivity, cationic demand and current retention figure. We reply with a program, a dose range and a machine-trial plan that a shift supervisor can run.

Reply within 12 working hours · data used for quotation only

Talk to us