Coagulant and flocculant,
specified as a system.
A treatment train that works is a sequence, not a shopping list: something has to neutralise the charge before something else can bridge the particles. Every product below states the number that decides its performance — molecular weight, charge density, Al₂O₃ content — because that is what a plant actually specifies.
Six products,
two jobs.
PAM bridges; PAC neutralises. Most plants need one of each, and the pages below explain which grade and why.
Anionic polyacrylamide
MW 5–22 million · hydrolysis 5–40 mol%
Tailings, coal washing, sand and aggregate, EOR, paper furnish. Four stocked grades.
GB/T 17514-2017
View product →FlocculantCationic polyacrylamide
Charge 10–80 mol% · MW 6–12 million
Sludge dewatering, DAF, paper retention, dyeing effluent. Charge density decides the cake.
GB/T 31246
View product →FlocculantNon-ionic polyacrylamide
Hydrolysis ≤ 5 mol% · MW 4–12 million
Acid leach circuits, coal preparation, drilling fluids, brine systems.
GB/T 17514-2017
View product →CoagulantPAC 28% industrial
Al₂O₃ ≥ 28% · basicity 40–90%
Industrial wastewater, sewage, paper, textile, metal finishing. Powder, granular or 10% liquid.
GB/T 22627-2022
View product →Coagulant · potablePAC 29% drinking water
Al₂O₃ ≥ 29% · insolubles ≤ 0.1%
Surface water, algal and low-turbidity water, colour, UF/RO pretreatment. Hygiene licence.
GB 15892
View product →ProgramPAC + PAM program
Matched ratio · jar-test protocol
Both chemicals specified as one system, with the dosing sequence, mixing energies and cost per m³.
Two-product system
View product →Start from the solids,
not from the product name.
Three questions narrow six products down to one or two. Answer them in order.
What charge are the solids?
Mineral and metal-hydroxide solids are negative — anionic PAM. Organic sludge and biological flocs are negative too, but they need a cationic polymer that also neutralises: cationic PAM. If the water is under pH 5 or above 3% salt, neither behaves well and non-ionic is the answer.
Is the water potable?
If yes, only two products qualify: PAC 29% for coagulation, produced under a hygiene licence, and a low-monomer anionic PAM at ≤0.025% residual acrylamide. Industrial PAC is not a substitute, and we will not supply it as one.
What is the plant's constraint?
Turbidity and colour take PAC. Settling rate and cake solids take PAM. If the constraint is cost per m³, the answer is usually a smaller PAC dose plus the right polymer — not more of either.
Before you request a sample.
Do you manufacture or trade?
We manufacture. Six production sites in Henan, PAC and PAM on separate lines, with in-house labs on each site. We are not a trading company quoting from someone else's price list, which is why we can tell you when a product is wrong for your application.
What is the minimum order?
Samples are free — 500 g for polymers, 1 kg for PAC, couriered at our cost for qualified projects. Trial orders start at 1 t; a 20-foot container holds 18–25 t depending on product and palletisation.
Which standards do you produce to?
Anionic and non-ionic PAM to GB/T 17514-2017, cationic PAM to GB/T 31246, industrial PAC to GB/T 22627-2022 and drinking-water PAC to GB 15892. We are a drafting unit of GB 15892 and GB/T 22627.
Can you supply a grade that is not on the list?
Yes, at 5 t minimum for polymers and 10 t for PAC. Hydrolysis, charge density and molecular weight can all be adjusted within the ranges shown on each product page; lead time is 20–25 days against 7–10 days for stock grades.
Do you hold NSF/ANSI 60?
No. We hold a Chinese hygiene licence for potable-water contact. If your specification requires NSF/ANSI 60, our drinking-water grades do not meet it and we will say so before quoting.
How do you handle quality claims?
Every batch ships with a COA. If a shipment fails your incoming test, we compare results against the retained sample, and if the batch is out of specification we replace it. Claims are settled on the retained sample, not on a conversation.
Not sure which of the six?
Send the water, not the product name.
Describe the stream — flow, solids, pH, target — and we will name the product and the dose. If the honest answer is that you need only one chemical, that is what you will get.
One system, not one chemical.
Dosage calculator
Estimate PAC and PAM demand from flow and suspended solids, with the dose uplift applied.
Open calculator →QualityQuality & certifications
Batch testing, COA content and the certificates we do and do not hold.
View quality →ApplicationsApplications
Six industries, each with its treatment train and dose reference.
Browse applications →