Home/Applications/Mining
Tailings · coal · acid leach · filtration

Mining: the water you get back
decides the cost per tonne.

A tailings thickener is a water-recovery device that happens to handle solids. We supply the coagulant and the flocculant as one matched pair — tested on your ore and your process water — so underflow density and overflow clarity move together instead of trading off against each other.

65–72%UNDERFLOW w/w
<300OVERFLOW NTU
85%+WATER RECOVERY
20–80g/t PAM
What goes into this water
PAC 28% industrialDestabilises clay and colloidal slimes before the polymer sees them.30–150 g/t solids
Anionic PAM A1210 / A1610Bridges into a floc that survives the rake and the underflow pump.20–80 g/t solids
Non-ionic PAM N06For acid leach circuits below pH 5, where anionic loses its charge.30–120 g/t solids
01 — Water profile

Four numbers decide
which grade you need.

We ask for these before quoting, because a grade recommendation without them is a guess. Most mines can produce all four from the metallurgical balance and a water analysis.

ParameterTypical rangeWhy it decides the grade
Solids content of feed15–45% w/wSets the PAM dose per tonne and whether a thickener or a paste thickener is the right device
pH of the slurry2–11Below pH 5 anionic PAM protonates and coils — that single fact moves the duty to non-ionic
Calcium + magnesium50–800 mg/LHardness ions help destabilise, so hard water needs less PAC and tolerates a lower-charge PAM
Particle size (P80)30–150 µmFine grinding means more surface area, more polymer and a slower-settling floc
Clay / slime fraction5–35%Clays hold water and blind filters; they dictate whether a coagulant is needed at all
Water recycle ratio70–95%Recycled water accumulates fines and reagents, which changes the optimum dose week to week
Send these six figures with a 2-litre sample and we return a dose curve, not a guess. The jar test is free; the courier is on us for qualified projects.
02 — Treatment train

Where each chemical sits.

Dosing in the wrong place is the most common reason a mine concludes the polymer “doesn't work”. The sequence below is the one that survives contact with a real plant.

FEEDThickener feedGrinding circuit or cyclone overflow, 15–45% solids.no chemical
RAPID MIXCoagulationPAC into the feed launder. 30–60 s at G 300–500 s⁻¹.30–150 g/t
FLOCCULATIONBridgingPAM into the feedwell, post-diluted. 60–120 s at G 50–100 s⁻¹.20–80 g/t
SEPARATIONThickenerRake 0.05–0.15 rpm. Bed depth and rake torque set the practical limit.—
RECOVERYOverflowClarified water to the process tank, target under 300 NTU.85–90% recovery
DISPOSALUnderflow65–72% w/w to tailings storage or paste plant.—

The two mixing energies matter as much as the chemicals: PAC needs violent mixing for less than a minute, PAM needs gentle mixing for one to two minutes. Put both in the same pipe and neither works.

03 — Recommended program

The program, matched to the duty.

Three products cover almost every mine water we see. Most plants need two of them, not three.

How we start. A jar test on your own slurry, run as a dose ladder for PAC and then for PAM, with settling rate, overflow turbidity and underflow density recorded at each point. You get the curves, not just a recommendation — so the plant can re-optimise when the ore changes.

04 — Dose reference

Dose reference by duty.

Figures are product per tonne of dry solids and already include the uplift we apply to textbook values to reflect plant practice. They are starting points for a jar test, not a design basis.

DutyCoagulantFlocculantTarget
Iron ore tailingsPAC 30–80 g/tA1210 25–60 g/tOverflow < 300 NTU, underflow 65–70%
Copper / lead-zinc tailingsPAC 40–120 g/tA1610 30–70 g/tOverflow < 250 NTU, underflow 68–72%
Gold CIL / CCDPAC 30–100 g/tA1610 25–60 g/tClarified overflow < 50 NTU for carbon circuits
Acid leach CCD (pH < 3)—N06 40–120 g/tOverflow < 200 NTU without pH adjustment
Coal wash waterPAC 20–60 g/tA1010 15–50 g/tRecycle water < 100 NTU
Concentrate filtration—A1210 10–40 g/tCake moisture down 2–4 points
For paste and high-density thickeners the polymer dose usually rises 20–40% against a conventional thickener, because the floc has to survive compression as well as settling. Test at the target bed height, not in a beaker on the bench.
05 — What goes wrong

Why a thickener stops working.

Four failures that account for most of the calls we get from mineral processing plants.

Overdosing the flocculant

Beyond the optimum the excess polymer re-stabilises the fines and overflow turbidity climbs while the bed gets mushy. If clarity worsens as dose rises, you are past the peak — cut 20% and re-run the ladder.

Single-point dosing into high shear

A centrifugal pump or a raw feed launder destroys the floc before it reaches the feedwell. Post-dilute to 0.05–0.1% and inject where the energy is under G 100 s⁻¹.

Ignoring the water chemistry

Hardness, sulfate and residual reagents from the mill all change the optimum. A grade that worked in July can underperform in December on the same ore.

Running without a coagulant

On clay-rich slimes, anionic PAM alone cannot adsorb — the surfaces are already negative. PAC first is not an upsell, it is the mechanism.

The economics. A thickener that recovers 85% instead of 78% returns roughly 7% of the process water. At 20,000 m³/d that is 1,400 m³/d of water the plant does not have to buy, treat or pump — usually worth far more than the polymer line on the cost sheet.
<300 NTUOverflow clarity target
65–72%Underflow solids w/w
85–90%Water recovery
20–80 g/tPAM consumption
06 — Questions from plant engineers

Before you run the jar test.

Can you match a competitor's product we are already using?

Usually, and we prefer to try. Send the current product's TDS or a 200 g sample plus your slurry; we run both side by side on the same ladder and report settling rate, overflow turbidity and underflow density. If ours is not better, we will say so.

Do we need both PAC and PAM?

On clay-rich or fine-ground slurries, yes. On clean, coarse, high-hardness tailings, anionic PAM alone often reaches target. The jar test answers this in an afternoon and the answer is worth real money over a year.

What about acid circuits below pH 3?

Use non-ionic PAM. Anionic PAM's carboxylate groups protonate at that pH, the chain coils, and bridging stops. Adjusting pH to suit a cheaper polymer costs more in lime than the polymer saves.

How does the trial work?

Free 500 g samples and a written ladder protocol. A 1 t trial order follows, then 20–25 t per container. Most mines go from sample to container in six to ten weeks, including the internal approval.

Can you supply to site, not just to port?

We quote FOB, CIF and DDP. Where we have a forwarder we deliver to site and handle customs; where we do not, we name the nearest port and work with your broker.

Next step

Send the slurry data.
Get a dose curve.

Solids content, pH, calcium and magnesium, P80 and your current thickener performance. With a 2-litre sample we return a ladder test report and a recommended grade.

Reply within 12 working hours · data used for quotation only

Talk to us