Home/Applications/Food & sugar
Cane & beet · starch · dairy · beverage

Food and sugar: clarification
you can measure in colour units.

In a sugar mill the flocculant is not a waste-treatment cost, it is a process chemical: it decides settling rate in the clarifier, mud volume and the colour that carries through to the crystalliser. In a food plant it is usually the opposite — a waste-treatment cost that has to be minimised.

40–200g/t cane PAC
5–20g/t cane PAM
<50 NTUCLARIFIED JUICE
PotablePROCESS WATER GRADE
What goes into this water
PAC 29% drinking waterProcess water and beverage-duty coagulation under a hygiene licence.10–50 g/m³
Anionic PAM A1010Cane juice and syrup clarification — fast floc, low residual5–20 g/t cane
Non-ionic PAM N06Beet juice and high-calcium systems; tolerant of pH and hardness10–30 g/t beet
Cationic PAM C80Protein and colloid removal in dairy, starch and food effluent5–25 ppm
01 — Water profile

Process side and
waste side are different jobs.

Sugar mills buy flocculant to make juice clear; food factories buy it to make effluent cheap. The same chemistry serves both, but the specification, the dose basis and the compliance story are not the same.

ParameterTypical rangeWhy it matters
Juice pH (cane)6.8–7.4 after limingOutside this band the floc does not form and colour carries to the pans
Juice turbidity200–2,000 NTUThe design parameter for coagulant dose; target below 50 NTU after clarification
Calcium (beet / carbonatation)300–1,500 mg/LVery high calcium changes polymer demand and favours non-ionic or low-charge grades
Temperature55–105 °CHot juice shortens polymer activity — dose close to the flash cooler, not upstream of it
Effluent COD500–5,000 mg/LSets whether coagulation alone is enough or biology is required
Process water standardPotableBeverage and dairy process water needs the potable-grade coagulant, not industrial
For sugar we ask for the juice analysis, the liming regime and the clarifier type. A tray clarifier and a short-residence clarifier need different floc — one wants a fast heavy floc, the other a slower, larger one.
02 — Treatment train

Where the chemicals sit.

In the mill the flocculant goes into the juice; in the factory it usually goes into the effluent. Two trains, one supplier.

EXTRACTIONCane / beet juiceMilling or diffusion; juice carries bagacillo and colloid.—
LIMINGpH adjustmentLime to pH 7.0–7.4 (cane) or carbonatation (beet).—
HEATING85–105 °CProtein and colloid coagulate with heat; the polymer then flocculates them.—
CLARIFICATIONPAC + PAMPAC into the limed juice, PAM into the flash tank or clarifier inlet.40–200 + 5–20 g/t
EVAPORATIONSyrupClear juice to the evaporators; colour carried here stays in the sugar.<50 NTU
EFFLUENTWash water & molassesPAC plus cationic PAM for COD and colour before discharge or irrigation.100–400 g/m³

Dose point matters more than dose in a sugar mill: polymer added upstream of the heater is destroyed by the temperature before it reaches the clarifier. Add after the heater, at the flash tank or clarifier inlet.

03 — Recommended program

Process chemical
and waste chemical.

The same three families, specified for two very different duties.

On food-contact compliance. Coagulants and flocculants used in food processing must comply with the rules of the destination country, and those rules differ. We supply the full heavy-metal COA and the product specification; confirming acceptance with your food-safety team and regulator is the buyer's step, and we will not imply a certification we do not hold.

04 — Dose reference

Dose reference.

Sugar doses are per tonne of cane or beet; effluent doses per cubic metre; process water per cubic metre.

DutyProductDoseTarget
Cane juice clarificationPAC 29 + A101040–200 g/t + 5–20 g/tClarified juice < 50 NTU
Beet juice / carbonatationPAC 29 + N0660–250 g/t + 10–30 g/tColour reduction, fast settling
Syrup / remelt clarificationPAC 29 + A1010100–300 g/t + 8–25 g/tColour and turbidity for crystallisation
Beverage process waterPAC 2910–50 g/m³Turbidity < 1 NTU
Food plant effluentPAC 28 + C80100–400 g/m³ + 5–25 ppmCOD removal 55–70%
Dairy / starch sludgeCationic C504–8 kg/t DSCake 20–28% DS
Sugar doses are quoted per tonne of cane or beet, which is how a mill budgets. Converting to g/m³ of juice requires the juice yield — roughly 100–110% on cane for a diffuser mill, lower for a conventional mill.
05 — What goes wrong

Where clarification goes wrong.

Four issues that show up as colour in the sugar or turbidity in the juice.

Polymer dosed before the heater

Heat above about 90 °C degrades the flocculant before it reaches the clarifier. Move the injection point downstream and the dose usually falls.

Wrong molecular weight for the clarifier

A high-MW tailings grade makes a large light floc that floats. Juice clarifiers want a modest MW and a fast, dense floc — A1010, not A2010.

Liming pH off target

Cane juice outside pH 6.8–7.4 will not floc properly no matter what is dosed. Check the liming control before the chemical.

Using industrial PAC for process water

Beverage and dairy process water needs the potable grade. The industrial product is not a compliant substitute and the COA will show why.

The sugar economics. Clarified juice below 50 NTU means less colour in the syrup, less colour in the crystal, and a higher ICUMSA value at sale. A flocculant that costs a few cents per tonne of cane can move the sugar price by more than that if the colour is what was limiting the grade.
<50 NTUClarified juice
<1 NTUBeverage water
55–70%COD removal in effluent
20–28%Cake solids
06 — Questions from plant engineers

Before you trial a food-grade program.

Which PAM for cane juice?

Anionic, low molecular weight — A1010 in our range. Juice clarifiers want a fast, dense floc that settles; a high-MW grade makes a light floc that floats and carries bagacillo into the overflow.

And for beet?

Non-ionic N06, because carbonatation liquor carries very high calcium and the anionic charge is screened out. Some beet mills run a low-charge anionic grade successfully; the jar test decides.

Is your PAC permitted for food processing?

We produce PAC 29% to GB 15892 under a hygiene licence for potable-water contact, and the batch COA carries the full heavy-metal panel. Whether that satisfies your destination market's food-contact rules is a question for your food-safety team — we supply the documents, we do not certify for you.

What about the effluent?

Cane and beet wash water responds well to PAC plus a cationic PAM: 55–70% COD removal is typical, with the remainder going to biology or irrigation. Molasses-bearing effluent is harder — it needs dilution and biology, not more coagulant.

Can you supply both process and waste chemicals in one container?

Yes, and most mills do exactly that: PAC 29% for juice and process water, anionic PAM for the clarifier, cationic PAM for the effluent plant. One container, three products, one set of documents.

Next step

Send the juice or effluent analysis.
Get a clarified answer.

Juice turbidity and pH, liming regime, clarifier type, or for effluent the COD, colour and flow. We reply with a product, a dose and a clarifier-inlet dosing point.

Reply within 12 working hours · data used for quotation only

Talk to us